Free Online Developer Tool

Sound & Noise Level Meter

Check sound levels around you using your device’s microphone. Monitor live audio levels and track changes over time directly in your browser.

Microphone-Based Live Sound Monitoring Sound History Free to Use
Microphone not started
Browser-based
Current signal level dBFS
— dBFS

Start the meter and allow microphone access to view the signal level.

Live Signal History

Recent microphone signal readings

60 seconds
Your signal history will appear here.
Minimum — dBFS
Average — dBFS
Maximum — dBFS

Select Start Meter to request microphone access.

Important: This tool measures relative digital microphone signal level (dBFS), not calibrated sound pressure level (dB SPL). Results depend on your microphone, device settings, and environment.

How to Use the Online Sound Level Meter

This online sound level meter analyzes the audio signal from your device’s microphone. Use it to observe changes in microphone signal strength, compare quieter and louder moments, and view a short history of recent readings.

  1. Open this page in a browser that supports microphone access.
  2. Select Start Meter and allow microphone access when prompted.
  3. Observe the live signal reading and the history chart as sounds occur around you.
  4. Review the minimum, average, and maximum signal readings for the current session.
  5. Select Stop to end measurement or Reset to clear the readings and chart.

What Does dBFS Mean?

The meter reports signal level in dBFS, which stands for decibels relative to digital full scale. It describes the amplitude of a digital audio signal relative to its maximum representable level. Values closer to 0 dBFS indicate a stronger digital signal, while more negative values indicate a weaker signal.

The displayed range is limited to -60 through 0 dBFS for readability. Very quiet signals may appear at the lower end of this display range. This visual range is not a calibrated measurement of the sound pressure in your environment.

dBFS vs. dB SPL

MeasurementWhat it describesCan this tool report it accurately?
dBFSDigital audio signal level relative to full scale.It can estimate the relative level of the signal received by the browser.
dB SPLPhysical sound pressure level relative to a reference pressure.Not without suitable microphone calibration and a validated measurement chain.

How Accurate Is an Online Noise Meter?

Browser-based measurements depend on the microphone, device hardware, operating system, audio processing, microphone gain, and surrounding conditions. Two devices may report different signal levels for the same sound.

This tool is intended for observing relative changes in microphone signal strength. It is not a calibrated sound level meter and should not be used for occupational noise compliance, hearing-safety decisions, legal evidence, or other applications that require certified sound pressure measurements.

Microphone Access and Privacy

The browser asks for permission before this tool can access your microphone. The tool’s JavaScript analyzes the incoming audio samples in the browser and does not include code to record or upload audio. Microphone access ends when you stop the meter, reset it, or leave the page. Browser and operating-system behavior may vary.

For the strongest privacy assurance, review the site’s other scripts and network activity as well as this tool’s code. The absence of an upload function in this component alone does not prove that every other component on a website is free of network requests.

Troubleshooting Microphone Access

  • No permission prompt: Check the microphone permission for this site in your browser settings.
  • No microphone detected: Connect or enable a microphone and check that your operating system recognizes it.
  • Readings seem unusually low: Check the selected input device and its input level. Avoid comparing readings from different devices as if they were calibrated.
  • The tool will not start: Open the page over HTTPS and use an up-to-date browser that supports the Web Audio API and microphone access.

Frequently Asked Questions

How do I measure sound online?

Open the online sound meter, select Start Meter, and allow microphone access. The tool displays the relative digital signal level and a history of recent readings.

Is this an accurate decibel meter?

It measures relative microphone signal level in dBFS, not calibrated sound pressure level in dB SPL. Its readings are useful for observing changes but should not be treated as professional or certified noise measurements.

What is the difference between dBFS and dB SPL?

dBFS describes a digital audio signal relative to its maximum level. dB SPL describes physical sound pressure. Converting microphone readings into reliable dB SPL values requires suitable calibration and a validated measurement setup.

Why does the reading change between devices?

Microphone sensitivity, input gain, automatic audio processing, hardware, and operating-system settings can all affect the measured digital signal. Readings from different devices are not directly comparable without calibration.

Does the sound meter need microphone permission?

Yes. The browser must grant microphone access before the tool can analyze audio. Microphone access generally requires HTTPS or another browser-approved secure context.

Does this tool record or upload my audio?

This tool’s JavaScript processes microphone samples in the browser and contains no audio-recording or audio-upload feature. Other website scripts and browser behavior are outside the scope of this component, so the complete site’s network activity should be reviewed before making broader privacy guarantees.

Can I use this tool for workplace noise compliance?

No. This tool does not provide calibrated sound pressure measurements or certified occupational noise assessments. Use suitable calibrated equipment and qualified guidance when compliance or hearing-safety decisions depend on accurate sound levels.